⭐ Since 2009 · Rated 4.7 from 700+ reviews

📍 Store and workshop in Hyderabad

7 min read

How to Bleed Hydraulic Disc Brakes: Shimano and SRAM

By Sampath V

How to Bleed Hydraulic Disc Brakes: Shimano and SRAM

Short answer: bleed hydraulic disc brakes when the lever feels spongy, pulls close to the bar, or the bite point keeps moving. Shimano, Tektro and some newer SRAM brakes use mineral oil, while most SRAM road and older SRAM MTB brakes use DOT 5.1 fluid, and the two must never be mixed. You need a bleed kit for your brand, the right fluid, a bleed block and about an hour. A mineral oil bleed kit costs from ₹1,035.

A hydraulic brake works by pushing fluid from the lever to the caliper. Air in that fluid compresses, so the lever goes soft and the brake feels weak. Bleeding pushes the old fluid and air out and fills the system with fresh fluid. This guide explains when you need to bleed, what you need for each brand, the basic method for Shimano mineral oil and SRAM DOT brakes, and when to bring the bike to a workshop instead.

  1. When your brakes need bleeding
  2. Mineral oil or DOT: check before you start
  3. What you need
  4. How to bleed Shimano and other mineral oil brakes
  5. How to bleed SRAM DOT brakes
  6. Mistakes that ruin a bleed
  7. FAQ
  8. Getting help with your brakes

When your brakes need bleeding

  • The lever feels soft or spongy, or pulls much closer to the bar than it used to.
  • The bite point moves during a ride, or you have to pump the lever to get full braking.
  • Braking fades on long descents, which can mean old fluid or air in the system.
  • After cutting or replacing a hose, or fitting a new lever or caliper.
  • On DOT systems, about once a year, because DOT fluid absorbs moisture over time.

Not every soft lever means air. Worn pads also make the lever travel further, so check the pads first. Our brake pad compatibility guide covers which pads fit.

Mineral oil or DOT: check before you start

Brake Fluid
Shimano Mineral oil
Tektro and most TRP Mineral oil
SRAM road hydraulic and older SRAM MTB (Level, G2, Code, Guide) DOT 5.1
SRAM Maven, DB8 and newer mineral oil models Mineral oil

The fluid type is printed on the lever or caliper. Putting the wrong fluid in swells the seals and usually means replacing the lever and caliper, so check every time. Our brake mount and fluid compatibility guide covers the details.

What you need

Item Example Price
Mineral oil bleed kit Ashima Bleeding Kit ₹1,035
SRAM mineral oil bleed kit SRAM Mineral Oil Bleeding Kit ₹5,150
SRAM DOT bleed kit IceToolz 54R5 Bleed Kit with Bleeding Edge adaptor ₹7,590
Mineral oil Alligator, Tektro or SRAM Maxima ₹690 to ₹1,290
Brake cleaner Juice Lubes Brake Juice ₹1,275

You also need a bleed block to hold the pistons apart, the right hex and Torx keys, a 7mm spanner for the bleed nipple, nitrile gloves, rags and isopropyl alcohol. Browse all disc brake and bleeding tools. Prices are indicative and move with exchange rates and import duty.

How to bleed Shimano and other mineral oil brakes

This is the common funnel method for Shimano. Tektro and other mineral oil brakes work in a similar way, but follow the maker's manual for your model.

  1. Prepare. Remove the wheel and the brake pads, and push the bleed block into the caliper. Never squeeze the lever without a block or rotor in place, or the pistons can pop out.
  2. Level the lever. Rotate the lever on the bar, or tilt the bike, so the bleed port on the lever is level and at the highest point of the system.
  3. Fit the funnel. Remove the bleed screw on the lever and screw in the funnel. Add some oil to it.
  4. Push oil up from the caliper. Fill the syringe with oil, tap out any air, and attach its tube to the caliper bleed nipple. Open the nipple a quarter turn with the 7mm spanner and push oil slowly up into the funnel until no more bubbles appear. Close the nipple and remove the syringe.
  5. Clear air at the lever. Squeeze the lever gently several times and flick the hose and lever. Bubbles rise into the funnel. Keep going until none appear and the lever feels firm.
  6. Close up. Put the stopper in the funnel, remove it, top up the port with oil until it overflows slightly, and refit the bleed screw with its O-ring.
  7. Clean and test. Wipe everything with isopropyl alcohol, refit clean pads and the wheel, and pump the lever until it feels firm. Bed in the pads with a few firm stops before riding fast.

How to bleed SRAM DOT brakes

SRAM's DOT method uses two syringes, one at the lever and one at the caliper, and pushes fluid through the system while pulling a vacuum to draw out air.

  1. Remove the wheel and pads and fit the bleed block. Set the lever's reach and contact adjusters as SRAM's manual specifies.
  2. Fill both syringes halfway with fresh DOT 5.1 fluid and remove the air from each by pulling a vacuum and tapping the bubbles out.
  3. Connect one syringe to the caliper, with the Bleeding Edge fitting on newer calipers, and the other to the lever bleed port.
  4. Push fluid from the caliper up into the lever syringe, then pull a vacuum from each end in turn to draw out trapped air.
  5. Close the system as the manual describes, clean all fluid off with isopropyl alcohol, refit the pads and test the lever.

DOT fluid damages paint and irritates skin, so wear gloves and wipe any spill immediately. Use fluid from a freshly opened bottle, because DOT absorbs moisture once open. If you have not bled DOT brakes before, it is worth having a workshop do it the first time.

Mistakes that ruin a bleed

  • Fluid on the pads or rotor. Contaminated pads squeal and barely stop, and usually need replacing. Take the pads out before you start.
  • The wrong fluid. Mineral oil in a DOT system, or the reverse, destroys the seals.
  • Air in the syringe. Tap out every bubble before connecting, or you push air into the brake.
  • Opening a system with a cut hose without the right parts. A new hose needs a new olive and insert, such as the Shimano SB-BH59 olive and insert (₹140).
  • Squeezing the lever with no pads, rotor or block in place. The pistons push out and the job gets much harder.

FAQ

How often should you bleed hydraulic disc brakes?

Bleed hydraulic disc brakes whenever the lever feels spongy, pulls close to the bar or the bite point moves, and bleed DOT systems such as most SRAM brakes about once a year anyway, because DOT fluid absorbs moisture, while mineral oil systems such as Shimano can often go much longer if the lever stays firm. Check pad wear first. Worn pads also make the lever travel further.

Can I use DOT fluid in Shimano brakes?

No, never put DOT fluid in Shimano brakes, because Shimano's seals are made for mineral oil and DOT fluid makes them swell and fail, which usually means replacing both the lever and the caliper, and the same damage happens if you put mineral oil into a DOT brake such as most SRAM road and older SRAM mountain bike brakes. The fluid type is printed on the lever or caliper. Check it every time.

Why is my brake lever still spongy after bleeding?

A lever that is still spongy after a bleed usually has air trapped near the lever, often because the lever was not level with its bleed port at the top, or because air was pushed in from a syringe that still had bubbles in it, and repeating the lever stage often clears it. Worn or contaminated pads also feel soft. If it persists, a seal may be leaking air.

Do you need to remove the wheel and pads to bleed brakes?

Yes, remove the wheel and the brake pads before bleeding, then fit a bleed block in the caliper, because the pads can be contaminated by any fluid that escapes and the block stops the pistons moving out while you work, which keeps the right amount of fluid in the system and makes the lever feel correct afterwards. Refit clean pads only after wiping everything with isopropyl alcohol. Bed the pads in before fast riding.

How much does it cost to bleed bike brakes at home?

Bleeding mineral oil brakes at home costs about Rs 1,800 to start, with a basic bleed kit at Rs 1,035 and mineral oil from Rs 690 that covers several bleeds, while a SRAM DOT setup with a Bleeding Edge kit costs about Rs 7,600 plus fluid, and each later bleed costs only the fluid. Add isopropyl alcohol and gloves. A workshop bleed is worth it if you are unsure.

Getting help with your brakes

The right kit and fluid depend on your brake model. Tell us your brakes and ask TBA Guide which kit and fluid you need, or bring the bike in for a workshop bleed.

How ToMaintenance

Related Posts

Water Bottles and Cages: Sizes, Insulated Bottles and Carrying More

Water Bottles and Cages: Sizes, Insulated Bottles and Carrying More

Group Riding: How to Ride Safely in a Bunch

Group Riding: How to Ride Safely in a Bunch

How to Set Up Your Cleats: Position, Angle, Width and Float

How to Set Up Your Cleats: Position, Angle, Width and Float

Shop Disc Brake & Bleeding Tools

In stock now, from this guide.

View all

Leave a comment

Please note: comments must be approved before they are published.